#5010 - Open Cell Rubber
#5010 - Open Cell Rubber
"Open-cell sponge rubber possesses an interconnected cell structure which will permit limited absorption and circulation of gases and fluids. Outer surface of the material is continuous (rather than porous) and exhibits good physical durability. Because air can pass freely between its cells, sponge offers a high degree of compressibility and displays fast recovery upon release from compression. Open-cell sponge is absorbent and should not be used where resistance to fluid penetration is required, unless protected with a surface coating. "
| #5010 - Open Cell Rubber (Anti-Skid) | ||||
| Thickness | Roll Width | Roll length (Yards) | Length (Feet) | Length (Meter) |
| 1/16" | 36" | 50 | 150 | 45.7 |
| 3/32" | 36" | 40 | 120 | 36.56 |
| 1/8" | 36" | 30 | 90 | 27.42 |
| 3/16" | 36" | 25 | 75 | 22.85 |
| 1/4" | 36" | 20 | 60 | 18.28 |
| 5/16" | 36" | 15 | 45 | 13.71 |
| 3/8" | 36" | 15 | 45 | 13.71 |
| 7/16" | 36" | 12 | 36 | 10.96 |
| 1/2" | 36" | 12 | 36 | 10.96 |
| 5/8" | 36" | 10 | 30 | 9.14 |
| 3/4" | 36" | 10 | 30 | 9.14 |
| 1" | 36" | 8 | 24 | 7.31 |
#5010 open cell rubber is available in 5 different compositions :
| ASTM D | RO11 | RO12 | RO13 | RO14 | RO15 |
| 1056-85 | |||||
| Designation | |||||
| ASTM D | 1A1 | 1A2 | 1A3 | 1A4 | 1A5 |
| 1056-98 | |||||
| Designation | |||||
| Compression | 2 - 5 psi | 5 - 9 psi | 9 - 13 psi | 13 - 17 psi | 17 - 22 psi |
| Deflection | |||||
| 25% | |||||
| Density | 25 Lb | 25 Lb | 25 Lb | 25 Lb | 25 Lb |
| Cubic Ft | Cubic Ft | Cubic Ft | Cubic Ft | Cubic Ft | |
| Minimum | Minimum | Minimum | Minimum | Minimum | |
| Tensil | 40 Lb | 40 Lb | 40 Lb | 40 Lb | 40 Lb |
| Square-Inch | Square-Inch | Square-Inch | Square-Inch | Square-Inch | |
| Minimum | Minimum | Minimum | Minimum | Minimum | |
| Elongation | Over | Over | Over | Over | Over |
| 250% | 250% | 250% | 250% | 250% |
This information is furnished as a guide for selecting materials. Multifeutre du Québec Ltée. disclaims liability for results or use of this information. It is the customer's responsibility to obtain and test samples when determining suitability of material for a particular application.
120W White Felt, 219-1 Gray Felt, 125B Blue Felt, 11075 Needle Felt , F26 Feutre Economy Felt, 218 Woven Felt, 303125 Brown Felt, 303 Decorative Felt (Craft) , 217 Non Woven (Lamp Base), 1001 Cork, 1002 Cork & Rubber, 2000 Red Rubber, 2002 Sponge Matting ( Antifatigue), 2003 AntifatigueMatting Pebble Finish, 2004 Solid Rubber Matting, 2005 Nitrile, 2006 Gum Rubber, 2007 Neoprene, 2008 SBR Rubber, 2010 Neoprene with Diaphragm, 2012 EPDM, 2080 Silicone, 4040 Polyethylene, 4050 XLPE Polyethylene, 4002 Ester Foam, 4051 Mounting Tape, 4052 EVA Foam, 4060 PVC Foam, 4080 Filter Foam, 5002-1 Neoprene Sponge SC41, 5002-3 Neoprene Sponge SC43, 5002-5 Neoprene Sponge SC45, 5001-1 Neoprene Sponge with Skin, 5003 EPDM Sponge, 5006-3 Ensolite IV3, 5010 Open Cell Rubber (Anti-Skid), 5080 Silicone Sponge, 8017 Flocked Paper, 8050 Hook & Loops, 8070 Clear Vinyl.
